Hawk T1/A Advanced Trainer

153 Topics 632 Posts
  • This topic is deleted!

    Pinned Locked
    1
    1 Votes
    1 Posts
    138 Views
    No one has replied
  • 10 Votes
    2 Posts
    5k Views

    v1.8 released

  • Paint kit

    Pinned Locked
    1
    0 Votes
    1 Posts
    311 Views
    No one has replied
  • Product Support

    Pinned Locked
    1
    0 Votes
    1 Posts
    517 Views
    No one has replied
  • Hawk T1 FAQs

    Pinned Locked
    1
    1 Votes
    1 Posts
    2k Views
    No one has replied
  • This topic is deleted!

    1
    0 Votes
    1 Posts
    5 Views
    No one has replied
  • Elevator trim not working

    5
    0 Votes
    5 Posts
    111 Views

    @jaspar11 I have just tested this and I am seeing the tail plan position indicator move between +5 and -3 by triggering the elevator trim assignments, so that sounds like there may be some other controller conflict that may be preventing the trim from working correctly for you.

    If you could kindly contact Just Flight support via the following link, they will be able to run through some troubleshooting steps with you to get you up and running: https://www.justflight.com/support

    Mark - Just Flight

  • Throttle idle lift lever

    3
    0 Votes
    3 Posts
    64 Views

    Thanks mark that works
    Just need to set up the rest of my warthog Hotas
    Standby for more silly questions

  • Ground handling nws

    3
    0 Votes
    3 Posts
    100 Views

    It’s works fine with other aircraft but not the hawk

  • Instantly running out of fuel

    2
    0 Votes
    2 Posts
    68 Views

    The logic we are using in the Hawk is that the aircraft will always load into a flight with 100% internal fuel (this will show as an approx. 65% fuel load as a 100% fuel load will only be possible if the external fuel tanks are fitted).

    One exception to this rule is if you have state saving enabled on the EFB from a previous flight, then the aircraft will load into the flight with whatever fuel was remaining in the tanks at the end of the previous flight.

    If you disable state saving on the EFB, any following flights in the aircraft will begin with a full internal fuel load.

    Mark - Just Flight

  • Does the pipper work?

    3
    0 Votes
    3 Posts
    68 Views

    Mark, this was quite helpful. I appreciate it.

  • Rudder trim reversed in v1.0.9

    2
    0 Votes
    2 Posts
    52 Views

    I have just tested this and the rudder trim is working in the correct direction using RUDDER TRIM LEFT and RUDDER TRIM RIGHT control assignments, as well as the Rudder Trim switch in the cockpit, so I believe this behaviour you are seeing is related to the flight model.

    I have logged this feedback on our internal bugs/feature request tracker for our flight dynamics developer to see, who is also currently working on some other changes to the Hawk's flight model. Unfortunately, we cannot give any timeframe for when an update will be released with these changes, but we will let everyone know via our normal channels.

    Mark - Just Flight

  • Xbox hawk performance

    1
    0 Votes
    1 Posts
    84 Views
    No one has replied
  • Wing tip vortices

    1
    0 Votes
    1 Posts
    64 Views
    No one has replied
  • 0 Votes
    3 Posts
    175 Views

    Scrub that. Just had a flight with a flight plan in and it just dominated all VOR ILS and TACAN navigation. No matter what switch selections I made I could couldn’t get out of gps nav.

  • How to configure throttle with Spad.next

    1
    0 Votes
    1 Posts
    85 Views
    No one has replied
  • Hawk T1/A

    1
    0 Votes
    1 Posts
    97 Views
    No one has replied
  • Takeoff issues

    1
    0 Votes
    1 Posts
    120 Views
    No one has replied
  • Ground speed / IAS discrepancy

    1
    1 Votes
    1 Posts
    91 Views
    No one has replied
  • Xbox release?

    17
    0 Votes
    17 Posts
    582 Views

    @jaydens you might want to head over to the marketplace and have a wander down the jet aisle.
    Have fun!