PA-28 Warrior II

@n293wk Great, thanks, and good advice on the heater. I'll do that next flight.

@d_isle That issue is now fixed in the latest version of the product available from your Just Flight account: https://community.justflight.com/topic/2476/update-change-logs-v0-3-5-released-edited-30-6-22

@jmarkows I'm stilling seeing the same issue after a full reinstall. I'm not relying on Auto. I have the mic set to com 1, Receive settings: Auto (off middle), com 1 (phone), com 2 (phone). Com 1 freq is set to CTAF and com 2 is set the AWAS. I can't hear the weather on com 2 until I switch the mic to Com 2. Very odd. I tested this in C172 classic and it worked fine. Is there another flag to tell the sim this capability exists?

@walterbeech 'Reduce' is probably a better choice of word than 'avoid', and it only affects the rear of the prop as seen from the cockpit

@wpa12 Recent post, easily found: https://community.justflight.com/topic/3557/any-plans-to-update-piper-series

Thanks for the feedback. We'll make this change for the next update.

There are no firm plans for alternative transponders at this stage as MSFS doesn't simulate ADS-B and has very limited transponder functionality but we'll certainly consider it if there is enough interest.

Do you mean that it doesn't move/animate or doesn't trigger the fuel pump to switch on?

@mgr Hello Marcel, thanks for confirming that I was on the right track. I then dug a bit deeper and noticed that I inadvertently had the extension .png.png.dds instead of .png.dds. It all works now Peter

@hamster892 Your best bet would be to contact Just Flight support. They can usually help with this kind of thing. https://support.justflight.com/support/home https://support.justflight.com/support/solutions/folders/17000139619 https://support.justflight.com/support/tickets/new

FIXED! I need to recalibrate my eyes. Simples! I went back to basics with the texture configs and the manifest; It turns out I switched a . with a , in the latter an was a . or two short in the texture.cfgs I had a brainfart during the community folder shuffle and loaded an older version. Thanks for all your help and patience. I now have a black leather VC with some German placards.

@jmarkows I guess ill do that. Thanks for the help!

@swissvirtualpilot Problem solved. have to delete the warrior folder in ...\Microsoft.FlightSimulator_8wekyb3d8bbwe\LocalState\packages restart sim. now it works.

@thorsten42 This is not new- https://community.justflight.com/topic/1783/battery-and-or-oil-will-not-recharge-plane-unflyable/8?_=1646763987562. Importantly, though, 8.8v is enough to run the avionics and start the engine

finaly, I need the file to start up with my logiteck panel ! I need too to open the valve of course Without the file I can start up with the mouse. The mistake was the valve. May be last time the data were still in memory, and deleting the file did'nt erase the data of the driver in memory I tried several times today, no CTD... May be CTD are depending something else... See you later

@syscd7000 We have replied to you on the TDS Sim Software forums.

Just a quick further update on this - current files for ME (so not released yet), which will be in the upcoming update: I'm testing out of Bidford as I know the field there rather well, the strip is roughly two and a half thousand ft, using standard ISA I'm taking a touch over a third the runway length to take off. It's not perfect, but given the upcoming prop adjustments it may get closer. Climb rate, 600fpm is the aiming point for the setting and it is the rate at which speed is stable. I can hit 900fpm if I pull the nose up, but the speed is decreasing, so as far as I am concerned it is on the mark.

@martyn Awesome, thanks so much!