X-Plane Products

Without knowing which exact annunciator has lit and under what circumstances lead up to it illuminating, it's a tricky one for us to confidently answer. The ANTI SKID FAULT annunciator will light if there is a fault within the system. The ANTI-SKID INOP annunciator will illuminate when the system is inoperative. With the latter, I believe it would only illuminate if the ANTI-SKID switch is set to OFF, or if the system does not have electrical power (Anti-Skid is supplied by DC Bus 2). If that behaviour occurs again, could I kindly ask you to raise a ticket with Just Flight Support via the following link: https://www.justflight.com/support If you could attach some screenshots or videos of the behaviour with the ticket, then our support team will be in the best position to investigate this further and assist with further troubleshooting. Mark - Just Flight

This appears to be the newest of the Threads about the Vulcan in XPlane 12 that I can find. From this and others it seems the only issues with the model built for V11 is the undercarriage and lights. can someone confirm that? and is JF planning on doing an update?

@razialaster you can move it using the VR controller. You need to use a VR controller to do it (i.e. the hardware controller that came with your VR set); you cannot move it with the mouse. Hover over its edges, using the VR controller (not the mouse), and you'll see that one of the edges lights up. Pull the trigger (or whatever button you use), and now you can place it in the VR world. It'll stay where you put it. This works, but you'll have to do it literally every time you turn on VR, even if you temporarily disable VR in the same flight... I don't know how to avoid that yet. See: https://community.justflight.com/topic/4613/panel-selector-is-in-the-way/6

The EFB in the Duchess Model 76 (X-Plane 12) features DynaFeel controls that can be used to adjust the force required to move each control surface. More information on DynaFeel and the other EFB features can be found in our GA Fleet Electronic Flight Bag (XP12) manual: https://www.justflight.com/product/duchess-model-76-xplane-12 With regards to Simbrief profiles, we don't have one created in house, but I can log that on our internal feature request tracker as something to investigate in the future. Mark - Just Flight

Using the 151 Sqn Tactical Weapons Unit model (X-Plane 11), I have managed to get the F5 20mm cannon to fire (no Aden 30mm, it seems), but I have not yet found our how to uncage the gunsight for air-to-air use - it should pull downwards under 'g', but remains fixed in the sightglass. Can anyone help with this, please?

I have been experiencing the same issue. I recently followed the videos recently posted to XPlaneOfficial's YouTube channel about troubleshooting issues like this. I ruled out the rudder pedals (input and flight control position values are consistent with my inputs) and convinced there is something wrong in the airfoil design of the Archer. You should be able to confirm similar by a) in flight configuration -> data output, search rudder and set "joystick aileron/elevator/rudder" and "flight controls aileron/elevator/rudder" to display in cockpit, b) start a new flight, c) Shift-8 to set the chase view, d) press Ctrl-m a few times until you see Elemental forces, and d) begin a regular takeoff. I also set video recording to a high quality and recorded to review at low speed. You'll see the position of the nose wheel properly aligns with the desired position on the rudder pedals. However, you'll see lateral forces on wheel do not match the input and expectation. However, you will also see significant lateral forces on the body of the airplane. While some of these forces make sense due to the airflow off the propeller, they seem fluctuate considerably and exceed the expected forces.

Greetings, I just purchased this wonderful aircraft, however I can't hear any touchdown sounds of the MLG, although the nose wheel chirps quite nicely. I have flown this aircraft IRL and know the touchdown sound is very prevalent, even with the smoothest of landings. I have all X-Plane sound sliders to the right and ensured the headphone jacks are not "plugged in". Any suggestions from the community would be most helpful. Regards

For the hidden VS enable/disable clickspot, you'd need to set 'L:AUTOPILOT_vs' to a value of 1. For VS increase/up clickspot, you'd need to set 'L:AUTOPILOT_vs_up' to a value of 1, and for VS decrease/down, you'd need to set 'L:AUTOPILOT_vs_dn' to a value of 1. In all three cases our systems code would reset those back to a value of 0, ready for the next trigger. If you would like to directly control the vertical speed, you should be able to use the MSFS 'AP_ALT_VAR_DEC' and 'AP_ALT_VAR_INC' key events. You should be able to toggle VS hold mode using 'AP_PANEL_VS_ON' and 'AP_PANEL_VS_OFF'.

We don't list the TDS GTNXi as compatible with the PA-28R Turbo Arrow III/IV (X-Plane 12), so I suspect there won't be any required code in the Turbo Arrow to make the GPS functional. We will, however, log this on our internal feature requests tracker as something to potentially look into adding support for in a future update. Mark - Just Flight

Sorry, just realised this is about X-Plane... doh! But I think the same applies - my TB10 in X-Plane sometimes needs reloading.