KA350 Condition Levers
-
-
@lemny it does work in Spad, see below how I have it implemented
In the client events page I have created the following events using the B:Vars
Below an example of axis setup in Spad.Next
axis range between 0 and 25 (Cut Off)
There's a delay in the axis movement so I added a check for the condition lever position != 0 so I could activate the repeat function to make sure no matter how fast I move the lever it will always catch up and get the position right - without such check of the condition lever position it would create an infinite loop (and we don't want to waste resource on that, right?! :) )axis range between 26 and 74 (Low Idle)
- the condition lever position must be != 1 in this caseaxis range between 75 and 100 (High Idle)
- the condition lever position must be != 2 in this caseThese are all script events hence I get the levers in the game in sync with my hardware all the time.
In case someone does not know where to find the Client Events page
Some extra 2 cents (out of topic)
There are some other events I have added you guys may find useful like events for the Radar, External Power, Pressurization Alt knob (yeah I also use the same event in the C414AW), for instance. Check it out!
Regards
Anderson
-
@meh1951 below follows how I setup feather in the KA
There are two events (axis change event & scripted event)
The axis change event is a regular one for controlling the propeller axis
The scripted event is the one that controls the feather position
Regards
Anderson
-
@anderson
I have tried to replicate this but I am not sure what the reference to Local:Joy_0X16D00X09C1_Slider is or where it came from. I do not have it on my system. -
@meh1951 you got to replace that by whatever the appropriate var for your hardware lever/switch/button is.
This var just tells spad.next whether that button/switch of your hardware position is pressed or not - for instance.
The key piece of information here is the PROP_PITCH2_SET (-25), that's the one that actually makes the lever move to the feather position in the game. -
@anderson
Could not get the feather to work that way but I did get it to work this way
Still have not got the Condition Levers to work :-(
-
@meh1951 for button 26 try to setup the following
Button Pressed -> Send PROP_PITCH1_SET - Event (-25) for Left Prop
For whatever the other button used for right prop set the following
Button Pressed -> Send PROP_PITCH2_SET - Event (-25) for Right Prop
The condition levers you got to create those events listed above first
Regards,
Anderson
-
@anderson
Yes I got feather wotking your way...thx
Yes I created the BVars and copied what you had minus the Joy
-
@meh1951 how are controlling the lever? Are you using one of the Bravo axis for that?
Show a printscreen of the Spad.Next setup you have for controlling the lever.
As per the printscreen you have sent before I guess your setup will be something like
LOCAL: search for RX_AXIS in the Bravo device list
The condition lever setup
Cut Off setup
If you are going to use a different axis just replace the RX_AXIS by the correct axis name
There will be 3 entries for each lever
0 - 25 Cut Off
26 - 73 Low Idle
75 - 100 High IdleYou may change these range values to whatever range is best for you.
Regards,
Anderson
-
@anderson
Thank you buddy the first screen shot answered a ton of questions for me.
I will try this...
thanks for your support!
-
@anderson
Does this look close??
-
-
@anderson
Repeat has been implemented but still the same results -
@anderson
Gone through a lot of programming but it's still the same results
-
@meh1951 the very first condition should be
Your condition is different
Turb Eng Condition Lever Position:2 equals ((LOCAL:JOY .... <=100))
Delete this Turb Eng Condition Lever Position:2
Your condition
The correct condition
There's no Turbo Eng Condition Lever Position:2 in the first line.
Give it a try as indicated.
Anderson
-
@anderson
Are you talking about the
While TURB ENG CONDITION LEVER:2 equals ?? -
@anderson not sure I know how to do that
?
