KA350 Condition Levers

meh1951

@anderson

Yes I got feather wotking your way...thx

Yes I created the BVars and copied what you had minus the Joy

hangar_101

@meh1951 how are controlling the lever? Are you using one of the Bravo axis for that?

Show a printscreen of the Spad.Next setup you have for controlling the lever.

As per the printscreen you have sent before I guess your setup will be something like

LOCAL: search for RX_AXIS in the Bravo device list

The condition lever setup

Cut Off setup

If you are going to use a different axis just replace the RX_AXIS by the correct axis name

There will be 3 entries for each lever

0 - 25 Cut Off
26 - 73 Low Idle
75 - 100 High Idle

You may change these range values to whatever range is best for you.

Regards,

Anderson

meh1951

@anderson

Thank you buddy the first screen shot answered a ton of questions for me.

I will try this...

thanks for your support!

meh1951

@anderson

Does this look close??

meh1951

@meh1951
No I still have problems.
Handle still not moving and Looping

Just realized I am getting 0 and 1 in the data monitor not 0 to 100 for the TURN ENG CONDITION LEVER

Failed again. Been working on this way to long.

hangar_101

@meh1951 you are almost there, notice you have not activated the repeat feature

It should be ON

You also can simplify the evaluation code by replacing the following line

by

Regards

Anderson

meh1951

@anderson
Repeat has been implemented but still the same results

meh1951

@anderson
Gone through a lot of programming but it's still the same results

hangar_101

@meh1951 the very first condition should be

Your condition is different

Turb Eng Condition Lever Position:2 equals ((LOCAL:JOY .... <=100))

Delete this Turb Eng Condition Lever Position:2

Your condition

The correct condition

There's no Turbo Eng Condition Lever Position:2 in the first line.

Give it a try as indicated.

Anderson

meh1951

@anderson
Are you talking about the
While TURB ENG CONDITION LEVER:2 equals ??

hangar_101

@meh1951 yes, scripted event window should look like this

Notice the first condition line just evaluates the lever position.

Anderson

meh1951

@anderson not sure I know how to do that

?

meh1951

@anderson
This is what I am supposed to have ... correct?

(([LOCAL:JOY_0X294B0X1901_Z_AXIS] >= 0) && ([LOCAL:JOY_0X294B0X1901_Z_AXIS] <= 25))

[TURB ENG CONDITION LEVER POSITION:2] != 0

B:FUEL_2_Condition_Lever_Cut_Off-Event

(([LOCAL:JOY_0X294B0X1901_Z_AXIS] >= 26) && ([LOCAL:JOY_0X294B0X1901_Z_AXIS] <= 74))

[TURB ENG CONDITION LEVER POSITION:2] != 1

B:FUEL_2_Condition_Lever_Low_Idle-Event

(([LOCAL:JOY_0X294B0X1901_Z_AXIS] >= 75) && ([LOCAL:JOY_0X294B0X1901_Z_AXIS] <= 100))

[TURB ENG CONDITION LEVER POSITION:2] != 2

B:FUEL_2_Condition_Lever_High_Idel-Event

hangar_101

@meh1951 correct. make sure repeat ON. If you want it to be exactly as the example I sent you use the is in range option for evaluating the axis value.

meh1951

@anderson
Was the screen shot at 28 correct?

or is this

hangar_101

@meh1951 it looks okay, notice you set range 0 thru 15 for Cut Off and 26 thru 75 for Low Idle, there's a gap between 16 thru 25. Recommend you change the Low Idle range to 16 thru 75.

Let me know if it works.(It should)

Anderson

meh1951

@anderson
Changed the range still does not work.

The logic works but the Levers never move

meh1951

@anderson
I got it! I don't know why but I was gonna work on and it was working today???
I really appreciate you sticking with be...I learned a bunch. Now I need to get some of this other stuff working. Thanks again!

For anybody else

meh1951

@anderson
Not working again...:-(

hangar_101

@meh1951 makes no sense unless you have the same lever setup somewhere else thus facing some sort of conflict. Verify that and also remove all mods but the KA mod itself from community folder.