Fuel Flow/Burn
-
So far, flying Adelaide to Sydney, with a TGT set to 645 I've been holding Mach .72 pretty solid at FL280 (1hr 10min so far). I easily reached 840 on take off as well, I don't think that has been a problem for me so far afaik (previously had been using 820).
Started with 7060kg of fuel, each engine is burning about 300kg/hr in cruise, burned 2500kg of fuel total according to the planes own gauges, leaving 4511 in the tanks afterwards. So there is definitely some discrepancy with its accuracy in the plane itself, but I figure that is because of the gauge style. Still According to this I should be able to fly back to Adelaide and nearly back to Sydney again, 1800nm total (and this isn't even with a full tank, a full tank is like 9400kg). So it does seem like the numbers a little bit on the low side? Since bad napkin math would put the range at about 2500nm. TBF, I had an average tailwind of like 40knots which would change these numbers a bit, but not that much surely?
@melon said in Fuel Flow/Burn:
So there is definitely some discrepancy with its accuracy in the plane itself, but I figure that is because of the gauge style.
We've confirmed it in a few other places but yes, the fuel burn (particularly in cruise) and TGTs are currently too low and we're working to address that.
-
Typical fuel consumption for BAe 146 during cruise is 2000 kg/h.
To achieve this, simply increase the fuel_flow_scalar value in the engine.cfg file. Standard value is 0.85
I changed it to 1.15 which makes the fuel consumption pretty realistic and in line with the calculations by SimBrief.[GENERALENGINEDATA]
engine_type =1
fuel_flow_scalar= 1.15
min_throttle_limit=-0.21 -
What do the profile options mean?
LIke... High Speed I assume is is maximum Thrust (using VS or IAS mode)? Long Range I guess is a lower power climb (ie 500-1000fpm). For descent I guess High Speed it essentially just an idle throttle high FPM descent over a shorter distance while Long Range is just that, idle or near idle descent over a much larger distance than the High Speed one?
For Cruise profiles, M70 is just maintain Mach .70 I guess, not to hard to work out. MCR is setting the TMS to Max Cruise Thrust, and just flooring it and riding the barber pole? LRC is low power cruise for max distance, like I'm guess .5 Mach or something?
Would be nice to get more information on what these meant, haha.
I haven't really had the issue with maintaining speed like some folks here have mentioned. It can be a little fiddly at the start with initial cruise, but after that its generally fine, usually letting me wander away or watch some Youtube while flying along.
@melon said in Fuel Flow/Burn:
What do the profile options mean?
I found this in a Mahan Air SOP for the BAE146/RJ
4. CLIMB Three climb techniques are recommended: 4.1.1 High Speed Climb (HSC): 280 IAS or 0.60 IMN. Coincident at approximately FL 190. 4.1.2 Long Range Climb (LRC): 250 IAS or 0.60 IMN, coincident at approximately FL 240. 4.1.3 Steep Gradient Climb: 220 KTS (146‐300).This technique can be used to reach a level or altitude by a particular point. For absolute max gradient performance, climb at VER (VFTO +10). Set climb thrust as soon as convenient (observe maximum 5 minutes) after flaps retraction, or at the thrust reduction altitude for the noise abatement procedure. [...] 6.5 DESCENT SPEED SCHEDULE: Two descent profiles are published: 1‐ Long Range 0.6M/250 kt 2‐ High Speed 0.7M/290 kt In practice, any combination of speeds can be used but ATC may require high forward speed to help fit the relatively slow BAe146 into the arrival flow with other, faster jets. For this reason the high speed profile is favored by many operators. Remember, to observe speed limit points and the limitation of 250 kts below 10 000 ft.As for TGT setting, the same SOP has
The normal power climb setting is 840 ºC TGT, although lower TGT may be used to conserve engine life if high climb performance is not required , (i.e.820 ºC) . -
@melon said in Fuel Flow/Burn:
What do the profile options mean?
I found this in a Mahan Air SOP for the BAE146/RJ
4. CLIMB Three climb techniques are recommended: 4.1.1 High Speed Climb (HSC): 280 IAS or 0.60 IMN. Coincident at approximately FL 190. 4.1.2 Long Range Climb (LRC): 250 IAS or 0.60 IMN, coincident at approximately FL 240. 4.1.3 Steep Gradient Climb: 220 KTS (146‐300).This technique can be used to reach a level or altitude by a particular point. For absolute max gradient performance, climb at VER (VFTO +10). Set climb thrust as soon as convenient (observe maximum 5 minutes) after flaps retraction, or at the thrust reduction altitude for the noise abatement procedure. [...] 6.5 DESCENT SPEED SCHEDULE: Two descent profiles are published: 1‐ Long Range 0.6M/250 kt 2‐ High Speed 0.7M/290 kt In practice, any combination of speeds can be used but ATC may require high forward speed to help fit the relatively slow BAe146 into the arrival flow with other, faster jets. For this reason the high speed profile is favored by many operators. Remember, to observe speed limit points and the limitation of 250 kts below 10 000 ft.As for TGT setting, the same SOP has
The normal power climb setting is 840 ºC TGT, although lower TGT may be used to conserve engine life if high climb performance is not required , (i.e.820 ºC) . -
What does the "co-incident at FLxx" mean? Do you set that speed at FLxx and climb, or do you climb at that speed until FLxx?
Thx
@b3lt3r They mean that 250 KIAS will equal Mach 0.6 at approximately FL240 etc. So if you were climbing at 250 KIAS then you could switch from IAS to MACH hold mode passing through approximatively FL240, and vice versa on the descent.
Martyn - Development Manager
-
@b3lt3r They mean that 250 KIAS will equal Mach 0.6 at approximately FL240 etc. So if you were climbing at 250 KIAS then you could switch from IAS to MACH hold mode passing through approximatively FL240, and vice versa on the descent.
-
@melon said in Fuel Flow/Burn:
@johan217 Oh that is really interesting, where does one acquire these sorts SOPs?
Some of these are floating around the interweb. I got this one from scribd (requires subscription, so I don't think I can share the full pdf here, sorry).
-
Apologies for the thread resurrection but this appears to closely relate to the issue I am seeing.
In the latest version in MSFS2024, I am seeing fuel burn numbers in the simulator approximately 50% lower than the Simbrief estimates. I am using the Just Flight 146 Simbrief profiles and I believe they are accurate, I believe the issue is on the MSFS side.
Is anybody else experiencing this? Is it potentially a regression of an earlier fix, either with the product or MSFS2024 itself?
I am using Kgs as the units, in case this has any bearing.
