146 Professional

655 Topics 3.3k Posts
  • This topic is deleted!

    1
    0 Votes
    1 Posts
    15 Views
    No one has replied
  • No APU Ops?

    12
    1 Votes
    12 Posts
    589 Views

    @b3lt3r So, I researched a little harder. The emergency start feature was not fitted to all aircraft. If it was fitted, there is a switch just under the avionics hatch that leads down from the cockpit to the avionics bay.

    I’ve crawled through that hatch many times so I know it intricately! Haha.

    I don’t’ think this JF version models this. JF gods, I hope you’re paying attention to this post. Please provide DC start and emergency battery start. 😝

    IMG_1452.jpeg

  • Additional Liveries (in the future?)

    1
    0 Votes
    1 Posts
    112 Views
    No one has replied
  • 0 Votes
    1 Posts
    315 Views
    No one has replied
  • Different failures rates explanied?

    8
    2 Votes
    8 Posts
    442 Views

    @baeflyer
    Well, that is most distressing.
    I have not had any failures but I had my failures set at real.
    I will be changing it to mid and see what happens.

  • Some 0.1.9 issues

    6
    0 Votes
    6 Posts
    587 Views

    @avionic I'm running one of two Honeycomb Bravo setups, and I'm not sure which one is used for the 4-engine binds. By default, one knob will trigger the selection of an input, e.g., ALT, V/S, HDG, etc., and the encoder will then simply bind to MSFS "plus" and "minus" functions. My other setup uses key combinations so the selector sort of acts as a "shift key" for the encoder, and HDG increase and decrease will be bound to "HDG input + encoder up/down". The 146 didn't use to respond to whatever I was using.

    I reported the vanishing keyboard in a ticket as well, that was the B-roll issue :-D

  • 0 Votes
    3 Posts
    186 Views

    @mark

    Ok, no worries. Thanks for getting back to me!

  • Landing practice in MSFS?

    5
    0 Votes
    5 Posts
    510 Views

    I noticed when loading a flight in the air and the engines are off, it usually helps to restart the flight or load the same flight again. For me it always fixed the problem that the engines don't start. Maybe it is related to state saving, which I have enabled in the EFB options.

  • 0 Votes
    2 Posts
    143 Views

    This isn't something we have experienced during testing on Xbox, but it is plausible that it may just be a performance-coping measure that is handled internally by the simulator on Xbox.

    Just speculation here as I don't have any knowledge of how the simulator works behind the scenes, but it may be that the simulator wants to keep a constant frame rate at all times, and to do that it is adjusting the scenery quality based on the current simulator's demands. So if you are flying a complex aircraft in scenery-intensive areas, it will have to reduce something to keep a constant frame rate, so it's choosing to reduce the scenery quality rather than the aircraft texture quality.

    I sadly suspect this is an issue that is out of our control but we will continue to monitor this issue and investigate internally for any possible improvements we can make in future updates.

    Mark - Just Flight

  • BAe146 V1.9: EFB SimBrief Error

    4
    0 Votes
    4 Posts
    576 Views

    Hi all,

    The EFB errors mentioned in this thread we believe are caused when the departure, destination, or alternate airport in the simBrief flight plan does not have any METAR data available. This will cause a red "METAR" error message to appear at the top right corner of the EFB, and potentially a "Loading..." message on the OFP page.

    This is something we are currently investigating and we are confident a fix can be developed and included in the next update to the 146 Professional.

    Mark - Just Flight

  • V0.1.9 EFB ERROR caused by alternate terrain

    1
    0 Votes
    1 Posts
    105 Views
    No one has replied
  • Question on the HSI

    7
    0 Votes
    7 Posts
    391 Views

    @lancealotg You have to way for flying: per VOR or HDG or RNAV. This pointer shows you the next navigation waypoint if you have programed your route in the FMC. If you select VOR NAV you will navigate with the VOR and HDG and the pointer willshow you the next programmed waypoint. If you fly with RNAV the HSI will agree with the diamond showing you the deviation from the navtrack.

  • This topic is deleted!

    1
    0 Votes
    1 Posts
    8 Views
    No one has replied
  • No sound click buttons with 3 positions

    1
    0 Votes
    1 Posts
    106 Views
    No one has replied
  • Landing and Throttle Use -- fun fact

    4
    4 Votes
    4 Posts
    445 Views

    @dirkster That's it yup.

    Watch the second landing I think... they don't touch the throttle as far as I can tell.

    I guess they just know their aircraft so well.

  • Restarting and engine in flight?

    5
    0 Votes
    5 Posts
    291 Views

    @gabe777 Yes, a pretty good one too. There is one linked on the product page where I'm not sure if it's the current one (it was a prerelease version with some issues when I last checked), and a more recent copy is in <your community folder>\justflight-aircraft-146\Documents.

  • 0 Votes
    5 Posts
    552 Views

    There is a pitch control toggle on the Pedestal.

    If you engage VS on the MCP, it will engage the AP and maintain your current VS rate.

    You can then use the Pitch control to adjust this.

    Or, if stable with AP Altitude ON... change the value in the Altitude window, then hit VS on the MCP, and adjust the VS rate using the pitch control.

    It will only work if you change the altitude.

    I use a button box with small trim wheels / Streamdeck, which makes this easier... but I'm sure you can find the relevant commands and assign a pair of buttons/rocker switch on one of your controllers ?

    (Don't forget VS should only really be used for small changes in altitude. IAS is the safest way)

    The Desc mode referred to above is not really relevant... it just tells you the minimum N2 (?) required for electrical systems etc to work properly.

  • No MAP in BAe146 EFB (version 0.1.9)

    6
    0 Votes
    6 Posts
    329 Views

    @mark Thank you!

    It is good to know that it is not something that I am doing wrong and that you are on it.

    Regards,
    Roberto

  • Thank you for implementing the failures!

    1
    3 Votes
    1 Posts
    166 Views
    No one has replied
  • 1.9 & Nav Radio

    1
    0 Votes
    1 Posts
    154 Views
    No one has replied