KA350 Condition Levers

Lemny

@meh1951 I figured that the condition lever axis in the sim works. But thats not a satisfying solution because you want the stuff in one place and profile and not a mix of ingame and simconnect stuff.

Voice of Reason

From the developer, hope this helps...

'The condition lever behavior is unmodified from the Asobo default behavior. I recommend using the following B:Vars, instead of the A:Var, though. That should ensure that the lever moves as it would in any default aircraft.

B:FUEL_1_Condition_lever_Cut_Off
B:FUEL_2_Condition_lever_Cut_Off
B:FUEL_1_Condition_Lever_Low_Idle
B:FUEL_2_Condition_Lever_Low_Idle
B:FUEL_1_Condition_Lever_High_Idle
B:FUEL_2_Condition_Lever_High_Idle

The L:Var for the master panel lighting switch is: L:var_masterPanelLights.'

meh1951

@voice-of-reason

The TURB ENG CONDITION LEVER POSITION:1 or 2 are also values 0, 1 and 2.
0 = cutoff
1 = low
2 = high

I can't find these variables but when I do I will try to get B:FUEL_1_Condition_lever_Cut_Off working

As a follow up not sure you can use B:Vars in Spad.Next

Confirmed B:Vars are not yet implemented in SPAD.Next

Lemny

@meh1951 said in KA350 Condition Levers:

As a follow up not sure you can use B:Vars in Spad.Next
Confirmed B:Vars are not yet implemented in SPAD.Next

Is confirmed to be in the next Alpha. I will test it out and post solutions here if the miussing stuff could be solved with B:Vars.

meh1951

@lemny
Thanks...just wanting to be able to feather.

Lemny

@meh1951 feather should work by simply set the standard prop axis to a huge negative value like -5000 IIRC. I could double check it tomorrow, but my feather settings worked on all my recent planes like C310, Baron and King Air.

hangar_101

@lemny it does work in Spad, see below how I have it implemented

In the client events page I have created the following events using the B:Vars

Below an example of axis setup in Spad.Next

axis range between 0 and 25 (Cut Off)

There's a delay in the axis movement so I added a check for the condition lever position != 0 so I could activate the repeat function to make sure no matter how fast I move the lever it will always catch up and get the position right - without such check of the condition lever position it would create an infinite loop (and we don't want to waste resource on that, right?! :) )

axis range between 26 and 74 (Low Idle)

- the condition lever position must be != 1 in this case

axis range between 75 and 100 (High Idle)

- the condition lever position must be != 2 in this case

These are all script events hence I get the levers in the game in sync with my hardware all the time.

In case someone does not know where to find the Client Events page

Some extra 2 cents (out of topic)

There are some other events I have added you guys may find useful like events for the Radar, External Power, Pressurization Alt knob (yeah I also use the same event in the C414AW), for instance. Check it out!

Regards

Anderson

hangar_101

@meh1951 below follows how I setup feather in the KA

There are two events (axis change event & scripted event)

The axis change event is a regular one for controlling the propeller axis

The scripted event is the one that controls the feather position

Regards

Anderson

meh1951

@anderson
I have tried to replicate this but I am not sure what the reference to Local:Joy_0X16D00X09C1_Slider is or where it came from. I do not have it on my system.

hangar_101

@meh1951 you got to replace that by whatever the appropriate var for your hardware lever/switch/button is.
This var just tells spad.next whether that button/switch of your hardware position is pressed or not - for instance.
The key piece of information here is the PROP_PITCH2_SET (-25), that's the one that actually makes the lever move to the feather position in the game.

meh1951

@anderson
Could not get the feather to work that way but I did get it to work this way

Still have not got the Condition Levers to work :-(

hangar_101

@meh1951 for button 26 try to setup the following

Button Pressed -> Send PROP_PITCH1_SET - Event (-25) for Left Prop

For whatever the other button used for right prop set the following

Button Pressed -> Send PROP_PITCH2_SET - Event (-25) for Right Prop

The condition levers you got to create those events listed above first

Regards,

Anderson

meh1951

@anderson

Yes I got feather wotking your way...thx

Yes I created the BVars and copied what you had minus the Joy

hangar_101

@meh1951 how are controlling the lever? Are you using one of the Bravo axis for that?

Show a printscreen of the Spad.Next setup you have for controlling the lever.

As per the printscreen you have sent before I guess your setup will be something like

LOCAL: search for RX_AXIS in the Bravo device list

The condition lever setup

Cut Off setup

If you are going to use a different axis just replace the RX_AXIS by the correct axis name

There will be 3 entries for each lever

0 - 25 Cut Off
26 - 73 Low Idle
75 - 100 High Idle

You may change these range values to whatever range is best for you.

Regards,

Anderson

meh1951

@anderson

Thank you buddy the first screen shot answered a ton of questions for me.

I will try this...

thanks for your support!

meh1951

@anderson

Does this look close??

meh1951

@meh1951
No I still have problems.
Handle still not moving and Looping

Just realized I am getting 0 and 1 in the data monitor not 0 to 100 for the TURN ENG CONDITION LEVER

Failed again. Been working on this way to long.

hangar_101

@meh1951 you are almost there, notice you have not activated the repeat feature

It should be ON

You also can simplify the evaluation code by replacing the following line

by

Regards

Anderson

meh1951

@anderson
Repeat has been implemented but still the same results

meh1951

@anderson
Gone through a lot of programming but it's still the same results