Mixture lever in 114TC not working
-
@craighl4 That's absolutely the easiest thing to do. It's what I do, in fact
@Black-Square Awesome. Thanks for confirming.
-
Is it feasible to bind the increase/decrease for the mixture to keypresses instead of a controller axis? I tried assigning it to every variation of Mixture 1 increase/decrease and couldn't get anything to work. The only thing that did have any effect was binding it to Mixture 1 axis. But I don't have an axis, so that's not particularly helpful.
-
@Woolies said in Mixture lever in 114TC not working:
I use the default Axis 0-100% for mixture no problems
I have apparently been using Mixture 1 Axis (-100 to 100) based on the bindings from the Bonanza that I copied for the Commander; an initial test showed that it seemed to work ok based on observed travel of the virtual lever and the engine running rough near cutoff, but I switched to Mixture 1 Axis (0 to 100) since the manual calls for the 0 to 100 values.
I'll have to fix that next time I fly my other Black Square planes.
-
@Woolies said in Mixture lever in 114TC not working:
I use the default Axis 0-100% for mixture no problems
I have apparently been using Mixture 1 Axis (-100 to 100) based on the bindings from the Bonanza that I copied for the Commander; an initial test showed that it seemed to work ok based on observed travel of the virtual lever and the engine running rough near cutoff, but I switched to Mixture 1 Axis (0 to 100) since the manual calls for the 0 to 100 values.
I'll have to fix that next time I fly my other Black Square planes.
@jmarkows I don't believe this is necessary. Nick confirmed that AXIS_MIXTURE_SET is OK to use. This equates to the -100 to 100% axis. I get full mixture lever travel when I use this axis.
I like to keep the same axis assignments for my different aircraft types (e.g. single prop airplane) to simplify my controller profiles in MSFS 2024. The MSFS aircraft such as the 172 need the -100 to 100 mixture axis to get full lever travel on my setup.
I then use MobiFlight for all non-axis assignments and have configurations per aircraft.
-
The mixture in the 114TC doesn't work with ctrl shift F2 or F3 to decrease it and increase it. The same is happening also to the non turbo Commander as well
@awash2002 It should work with all native bindings. Can you tell me specifically what you have bound to those keys?
-
Since the new patch, my standard mixture up/down binds that ive used for everything in 2024 and 2020 no longer work in the 114 turbo or non turbo. They still work in other planes Ive tried. I can still move the mixture with the mouse, but the binds dont work anymore. Buttons on my TWCS throttle bound to " decrease mixture" and "increase mixture". No external software involved. Sounds like same issue as @awash2002 but im curious if theirs worked before the patch.
-
Same. It worked for me earlier today since I bought the plane. This evening I found out there was an update. I installed it. The mixture is not working anymore. Thrustmaster Warthog HOTAS user. I mapped it to the Increase/Decrease Mixture, as I do for every GA plane with a mixture control. It was fine until the update.
-
Since the new patch, my standard mixture up/down binds that ive used for everything in 2024 and 2020 no longer work in the 114 turbo or non turbo. They still work in other planes Ive tried. I can still move the mixture with the mouse, but the binds dont work anymore. Buttons on my TWCS throttle bound to " decrease mixture" and "increase mixture". No external software involved. Sounds like same issue as @awash2002 but im curious if theirs worked before the patch.
@rinkerbuck Your post was a the key. I found the issue. It was a find-and-replace error. All bindings seem to be working again on my end. I'll publish an update asap for this. Thanks, everyone. Sorry for the mistake.
-
@awash2002 It should work with all native bindings. Can you tell me specifically what you have bound to those keys?
@Black-Square I use ctrl shift F2 for decrease and ctrl shift F3 for mixture increase
-
@rinkerbuck Your post was a the key. I found the issue. It was a find-and-replace error. All bindings seem to be working again on my end. I'll publish an update asap for this. Thanks, everyone. Sorry for the mistake.
@Black-Square default set pitot heat key-bind not working in 1.1 as well***
CPL MIFR 🍁
-
yay! Thanks for your work on this.
-
@Black-Square default set pitot heat key-bind not working in 1.1 as well***
@SadBucket said in Mixture lever in 114TC not working:
@Black-Square default set pitot heat key-bind not working in 1.1 as well***
It was confirmed in another topic that you need to use the Lvar (manual on the website has been updated to reflect this), and not the Kvar/default binding.
-
@Black-Square default set pitot heat key-bind not working in 1.1 as well***
@SadBucket It's because of the state saving system. I have to draw the line somewhere between what people expect to be an easy native binding, and "L:var_SecondaryFuelValveEmergencyPushLatching_Cover_L_R".
