Turbo Arrows not working correctly after sim update 5
-
hey...
some issues i run into after a short break with the sim...-
autopilot gets crazy when engaging
when pressing the HDG button (hdg is sync with the runway)
the yoke turns immediately to the left
same with NAV it turns slowly to the right -
have no magenta line in the Garmin` s when loading a plan
instead i have weird waypoint names that actually not in my flight plan
(i have to say , i use the pms50 GNS 530 mod)
minor isssues
-
interior co pilot model is gone
-
oxygen toggle is gone ( i think it was the "dump air" event in the sim)
very disapointed with the last su5 (not your fault .. i know)
thanks in advance
-
-
hey...
some issues i run into after a short break with the sim...-
autopilot gets crazy when engaging
when pressing the HDG button (hdg is sync with the runway)
the yoke turns immediately to the left
same with NAV it turns slowly to the right -
have no magenta line in the Garmin` s when loading a plan
instead i have weird waypoint names that actually not in my flight plan
(i have to say , i use the pms50 GNS 530 mod)
minor isssues
-
interior co pilot model is gone
-
oxygen toggle is gone ( i think it was the "dump air" event in the sim)
very disapointed with the last su5 (not your fault .. i know)
thanks in advance
@stefan Just checking, you have updated since we released our update last week/
-
-
@stefan Just checking, you have updated since we released our update last week/
@voice-of-reason I have the latest version of the Turbo arrows installed. I went through programs and features to completely remove the last versions I had installed, then ran the new versions installer. The plane works well now, however, when flying on VATSIM, I noticed COMM1 and 2 and the transponder will change to a random set of numbers when airborn. On the ground they seem to stay as you set them. Once I takeoff, they all just change, making flying on VATSIM impossible. Tried with the GNS mod and without it. Same result both times.
-
@stefan Just checking, you have updated since we released our update last week/
yes i have 0.4.0 in my comunity folder (also the newest pms50 mod)
i removed the old version from the com folder and reinstalled it via the new 0.4.0 .exe installer
should i try to remove it completely from my system and install again ?
-
yes i have 0.4.0 in my comunity folder (also the newest pms50 mod)
i removed the old version from the com folder and reinstalled it via the new 0.4.0 .exe installer
should i try to remove it completely from my system and install again ?
-
@stefan Yes, give it a go. If your problems persist please raise a ticket with our support team.
@voice-of-reason
unfortunately no success... i opened a ticket ...thanks so farbtw...
would it be possible to add a small indication to the EFB when the ALT hold mode is active ?
i disabled the ugly looking cockpit tooltips in the sim ... but now its hard to check the state -
@voice-of-reason I have the latest version of the Turbo arrows installed. I went through programs and features to completely remove the last versions I had installed, then ran the new versions installer. The plane works well now, however, when flying on VATSIM, I noticed COMM1 and 2 and the transponder will change to a random set of numbers when airborn. On the ground they seem to stay as you set them. Once I takeoff, they all just change, making flying on VATSIM impossible. Tried with the GNS mod and without it. Same result both times.
@tailspin88 This actually seems to be a bug in the sim, not specific to the Arrows. I tested with the default C208 and it does the same thing with the radios not staying as you set them.
-
My Turbo III is now missing. No idea why. Arrow III and Turbo IV and Warrior II are all there, but the Turbo III is gone. Ugh. When I check the directories, the files are there.
Brian
https://www.flyaka.com
Alaska Adventures -
My Turbo III is now missing. No idea why. Arrow III and Turbo IV and Warrior II are all there, but the Turbo III is gone. Ugh. When I check the directories, the files are there.
I found it today. For some reason it shows up in the aircraft list as UI_Aircraft.... something something. It's there, but it has a bad manifest
-
@tailspin88 This actually seems to be a bug in the sim, not specific to the Arrows. I tested with the default C208 and it does the same thing with the radios not staying as you set them.
@tailspin88 This isn't a problem in the sim. I've helped a few people fix this. When SU5 was released, it created a LOT of changes in your settings to take advantage of the new options available. The problem is that you have the AI set up to control your radios but you didn't know it. Go into your options and turn off the AI radio control
