Missing Documentation of LVars and stuff

[Black Square]

Hi Lemny,

All the switches on the overhead panel, including the starter switch, can be controlled via L:Vars. Here's the last from the AnalogTBM.xml:

var_crashbar
BKSQ_SourceSwitch
BKSQ_GeneratorSwitch
var_MainGeneratorResetButton
var_StandbyGeneratorResetButton
BKSQ_StarterSwitch
BKSQ_IgnitionSwitch

Hope that helps increase your immersion,
Nick C.

[Lemny]

@Black-Square Hey Nick, thanks a lot... sure it will... 🙂 I try them out in a minute.

I also updated my 4-Pack gauges on my mobile living room cockpit for the TBM.
Love this gem of a plane. 😍

[Lemny]

@Black-Square
Nick!!! WTF?! I feel stupid now... you literally put the whole documentation I was looking for all the time in the AnalogTBM.xml.
That was all I need... why did you not put the remarked section in the manual... my whole stupid post here would be obsolete. 😍🤣

EDIT: DONE!!! Bound nearly every switch of this beauty... 😀

[kaptenek]

Have got many things to work, but the switches for prop deice dont move. Any ideas?

Kind regards

Patric

[Lemny]

@kaptenek
The whole deice stuff works perfectly with the Stuff mentioned in the AnalogTBM.xml for me.
Including moving switches.

var_airframeDeice
Ice/Wing Light Switch 				Use Native Binding
Propeller Deice Switch 				Use Native Binding
L Windshield Heat Switch			"L:var_windshieldHeatSwitch_L, bool"
R Windshield Heat Switch			"L:var_windshieldHeatSwitch_R, bool"
Pitot Heat 1 Switch 				Use Native Binding
Pitot Heat 2 Switch 				Use Native Binding
Inertial Separator 					"L:var_InertialSeparatorSwitch, bool"

[kaptenek]

All that works fine also, but i cant get the seitch to move Honeycomb Alpha switch

[Lemny]

@kaptenek said in Missing Documentation of LVars and stuff:

All that works fine also, but i cant get the seitch to move Honeycomb Alpha switch

What du you mean? Do you want to move the Alpha switches if you use them in the sim?

[kaptenek]

I meen when i move my switches on my hardware Honeycomb Alpha, the switches dont move in the sim. However the corresponding lights for prop deice turns on. Using the settings in the xml

Best regards

[Lemny]

That‘s strange… with my settings above they move correctly

[Black Square]

Lemney's settings should move the switches in the cockpit, to the best of my knowledge. Using the K:Events will only work for some switches, but now that B:Vars are available in 3rd party products like Spad, those should be used whenever possible. Let me know if you're still having difficulties, and I can look into it.

[kaptenek]

I use spad, for it. Every switch works perfect exept for propeller deice.

[Black Square]

I just tried the B:Var in the debugger, and it flips the switch. Try:

(>B:DEICE_Propeller_1_Toggle)

and if that doesn't work, try using:

([0/1] >B:DEICE_Propeller_1_Set)

[kaptenek]

I Will try and post a screen shoot

[Lemny]

I just double checked and tried it again and can confirm

with 1 or 0/nothing switches the prop deicer on an off and moves the switch.

The SimConnect

only changes the lamp (and I assume the deicer) but not the switch.

[kaptenek]

Thanks so much all of you, that did the trick

[kaptenek]

Is it possible via Spad and Streamdeck to ”close” the flashing orange MSG GPS?

And also via Spad and Streamdeck to switch the middle button Nav to desired nav source?

Thank in advance

[Lemny]

I don't know out of my head the exact event, but I have bound a Streamdeck button to CDI (that switches the main HSI from Localizer to GPS and back) and it is working with all Versions (530, 750 PMS and TDS) I can look into it later.
And the Master Caution and Warning I have also bound... But I don't know if the MSG Lights are similar. I will tell here if I find something.

[kaptenek]

Would be great if you could help me out Lemny

[Lemny]

@kaptenek

The CDI are easy to find in SPAD. They all working. I

I use there two on my Streamdeck button:

For the MSG alert

did the trick.

[kaptenek]

This is wonderfull… Thanks