Black Square Custom Failure Notes

[ksmith]

There are a couple of sync issues with the sync of the display when H:Event are used to toggle failures.
Here are 2 use cases specifically:

USE CASE 1, "show only active failures ENABLED"

1. Here are two failures being toggled remotely in the TBM (causing them to enter FAIL state, as expected)
   

The tablet shows the state correctly.

2. I then toggle the R BRAKE, causing it to be fixed...
   

ALL GOOD SO FAR.

3. Lastly, I toggle the GEAR CONTROLLER, which was the only remaining failure. This fixes it as expected however the LAST item isn't cleared from the list and remains in red. Notice ACTIVE FAILURES is 0, which is correct:
   

4. if I click RESET on the tablet....it actually triggers the failure... (photo taken after clicking RESET)
   

5. if I click RESET on the tablet AGAIN...it works as expected, 0 failures and clear panel:
   

USE CASE #2: "Show only active failures DISABLED"

1. I click R BRAKE and toggle remotely (triggers a fail, as expected)
   

2. I click R BRAKE and toggle (triggers a fix, as expected). Notice the tablet remains RED for that item, despite Active Failures correctly updating to 0.
   

The same behavior from use case #1 also happens here where if I click RESET on the tablet, it things it's resetting but it's actually toggling to fail mode...it then takes ANOTHER reset to clear.

Keith Smith
PilotEdge

[Buzz]

Turbine Duke - Prop Governor Failure
During a failed prop governor, with indications showing an inability for the governor to push the prop to fine pitch (Lower RPM than set with prop lever) we would expect to see a drop in oil pressure to confirm due to a leak at or before the governor. With the TDuke, a Governor failure causes a drop in RPM, (Inability to drive the prop to fine pitch), but we still have prop control along the lower band of the prop lever, which would indicate a low oil pressure condition at the governor. Maybe a fix in the future, or atleast corrected for any future Turboprops?

[Buzz]

All Black Square Aircraft - Pitot Blockage
When a "Pitot Blockage" is triggered, the pitot heat switches get locked in the current position, regardless if they are on or off. Would it be possible to free up the switches from there locked state after a pitot tube blockage so that we can work through the failure procedure?

[jmarkows]

@Buzz said in Black Square Custom Failure Notes:

All Black Square Aircraft - Pitot Blockage
When a "Pitot Blockage" is triggered, the pitot heat switches get locked in the current position, regardless if they are on or off. Would it be possible to free up the switches from there locked state after a pitot tube blockage so that we can work through the failure procedure?

https://community.justflight.com/topic/9708/pitot-blockage-disables-the-pitot-heat/4?_=1775437463744

That one is a sim issue.

[Buzz]

@jmarkows Thanks.

[Black Square]

@ksmith Hi Keith! Thanks for posting this here. I'm sorry that I haven't been as responsive over email as I have been here. Just a habit of what I check and when. My apologies.

I believe I've fixed this for you guys. Pretty simple solution if you want to try it yourself. If you search for BlackSquareTablet.js, and then the comment containing Initiating HTML Failure for:, add the following block of code right before the next return;

if(this.onlyActiveFailuresSwitch.checked)
    this.updateFailureFilter();
this.updateFailureBlock(this.failureMatrix[i]);

I'm pretty confident that should fix all the synchronization problems you noted, so I will add that to all my other aircraft too. Let me know if that works, and if there is anything else I can do for you!

[ksmith]

@Black-Square That fixes both use cases, thank you.

[Black Square]

@ksmith Wonderful! Thanks for the feedback. Let me know if there's anything else I can do for you guys!

[Buzz]

Blacksquare Baron P.

When an alternator check is done during runnup, taking one of the two alternators offline prompts an annunciation light. When a single alternator failure is triggered, we lose voltage for the failed alternator but we receive no annunciation light even though the failed alternator is not putting out any voltage.

Once voltage drops below a certain threshold, we should receive a light.

[Black Square]

@Buzz Easy fix. Thanks.