Unable to control landing gear with Honeycomb Bravo Throttle Quadrant
-
@katchaplin
Thank you for your reply. The Bravo also has its own configuration which is the Honeycomb Bravo Profile I was talking about. The issue is the Arrow III only responds to the "TOGGLE LANDING GEAR" variable which would require the Bravo's gear handle to be cycled up and down to either raise or lower the gear. That happens because the Bravo landing gear up/down switches are either continuously on or off rather than pulsed on as in my other controller which sends a single control pulse when the gear handle is either raised or lowered. -
@sdvpilot I don't have the Honeycomb either, so just sort of guessing, but there is a control option for Gear Up and Gear Down in the options, can you set the handle up or down with those, rather than a toggle? Or are you saying that those aren't mapped with the Arrow?
-
Here are my BRAVO landing gear command assignments, which work perfectly with the Arrow III on my system.... Check to make sure you don't have additional landing gear command assignments on the BRAVO, or on any other controller that might be conflicting with it. -
This post is deleted!
-
@retiredman93231
The Arrow is not responding to GEAR UP and GEAR DOWN assignments for the Bravo Gear control on my system. With those assignments the gear cannot even be raised using the mouse in the cockpit. However the Beechcraft G36 responds as expected. The Arrow landing gear only responds to TOGGLE LANDING GEAR.
As you suggested I confirmed that no other controller and no other Bravo control is assigned any landing gear variable. I also removed addon liveries and alternate interiors for the Arrow from my community folder. I am experiencing the same behavior with the Turbo Arrow. -
@sdvpilot With the GEAR UP and GEAR DOWN commands assigned to a BRAVO toggle switch you will not be able to use the mouse to raise or lower the gear, because the switch will always be sending one command or the other, which will override the mouse input.
To make sure that you don't have these commands double assigned to any other switches or buttons, use the "search by name" box on the command assignment window... it should then list all of the current switches assigned for that command. Do this for each controller...
-
@retiredman93231
As I said the Bravo gear control works perfectly with the Beechcraft G36 using GEAR UP and GEAR down command variables. So that would indicate that there are no other conflicting assignments. I have also searched as you suggest to confirm that no other controllers have landing gear command assignments. The issue seems to be with my Arrows. When using those command variables the Arrow's gear appears to be stuck in the down position. The gear does cycle in response to the TOGGLE LANDING GEAR command variable which would not be the case if something else was holding the gear down. It looks like there is just no response to the GEAR UP command. Very strange! I am thinking of trying a re-install on the Arrow to see if this issue persists. -
@sdvpilot Very strange indeed! I think a reinstall is worth a try... You might want to even re-download it as well, just to be sure you have the latest version, and it wasn't corrupted during the previous download.
-
@RetiredMan93231
I was thinking the.same because I only recently acquired the Bravo. Previously I used the desktop aviators landing gear panel. with FSUIPC7 and the GEAR TOGGLE command. -
@sdvpilot If you wait a few days to re-download and re-install it, JF might release their long awaited update... I think they are very close now, and they might be just waiting for SU7 to drop this week, to be sure that nothing else breaks after that update.
-
@RetiredMan93231
Yes I was debating with myself about holding off until the next Arrow update. And who knows what SU7 will bring to the table. Don' t know if you are interested but I have been looking to expand the capabilities of the Bravo to make use of the right side adjustmen knob to operate as many virtual knobs as possible. I just added my post to https://forums.flightsimulator.com/t/taking-the-honeycomb-bravo-to-the-next-level-advanced-configs/379768/20?u=sdmaxpilot -
@retiredman93231
I found the same strange behavior after downloading and. re-installing the Arrow III. With further testing I was able to determine that it simply does no respond to the GEAR UP command variable while it does respond to GEAR DOWN. So if I raise the Bravo gear control I can only raise the gear via. the mouse in the virtual cockpit. However once the gear is up it can be lowered by lowering the Bravo gear control.
For now I will just continue to use my Desktop Aviator Landing Gear Panel with FSUIPC7 issuing GEAR TOGGLE commands to the simulator. I like the feel of it better than the gear handle on the Bravo anyway. -
@sdvpilot said in Unable to control landing gear with Honeycomb Bravo Throttle Quadrant:
I found the same strange behavior after downloading and. re-installing the Arrow III. With further testing I was able to determine that it simply does no respond to the GEAR UP command variable while it does respond to GEAR DOWN. So if I raise the Bravo gear control I can only raise the gear via. the mouse in the virtual cockpit. However once the gear is up it can be lowered by lowering the Bravo gear control.
As a work around, you could try assigning GEAR DOWN to the down position and GEAR TOGGLE to the up position... But, something is definitely wrong with your ssytem, since the default Gear Up/Down assignments work OK on my system, and I suspect on many others based on the absence of more complaints from other users.
I have seen some really strange bugs appear from conflicts with mods in the Community folder... Have you tried temporarily moving absolutely everything except this aircraft from the Community folder to a backup desktop folder, to completely eliminate that possibility?
-
Fellow bravo user here, no problems. Either in spad using gear up/down or through the sim.
I would suggest triple checking you settings. Literally today out of nowhere, my landing light was stuck in an on position. Found that in the sim under my custom bravo profile, which is supposed to be completely empty, had landing lights assigned to one of the switches. I know I didn't put it there. Not the first time things have spontaneously appeared in there lol.
Another option...you may have a flaky switch. I've had my bravo for almost a year now and had 2 switches that were acting odd. And I swore up and down it was the plane, as when I jumped into another, it was fine. I tend to spend most time in one plane for long stretches, so when it worked in another, it has to be the plane right? This went on for a month or two till it finally happened in a different plane. After squirting some contact cleaner in the switches they're fine now.
Try assigning the gear to one of the switches instead of the gear lever and see what happens.
-
@RetiredMan93231
By lowering the gear with the mouse and assigning another known working Bravo switch to the GEAR UP command I think I have established thar the Arrow is just not responding to the GEAR UP command for some strange reason. I also assigned the Bravo GEAR up switch to the gear down command while raising the GEAR with the mouse to confirm that that switch works. I will try eliminating all other addons from my community folder leaving only the Arrow III. -
@retiredman93231
Just emptied the community folder except for the Arrow Iii. Again there was no response to the GEAR UP command. assigned by. any known working Bravo switch. -
@sdvpilot Do a "Search By Name" for GEAR DOWN" and for "GEAR" to see a full list of all mappings for this command. And also do it for all of your other controllers... Something must be preventing the GEAR UP command from working??
-
@retiredman93231 Verified that no other switches from any other controllers are assigning the GEAR UP command. Also verified that there is no response to the GEAR IP command when it is assigned from a switch on another controller while the GEAR DOWN command does work from that same controller switch.
-
@retiredman93231
Thanks I now see the notification in my email. I have run out of time for now but look forward to trying out the updates. I did also verify that only my 3 Arrows refused to respond to the GEAR UP command. Every other RG aircraft responded as expected. I am surprised they would release the update just before SU7 unless the just want to see what happens.
