Skip to content
  • Categories
  • Recent
  • Tags
  • Popular
  • Users
Collapse
Just Flight Community Forum
  1. Home
  2. Just Flight
  3. P3D & FSX Products
  4. DC Designs Concorde
  5. Overspeed / Loss of Control

Overspeed / Loss of Control

Scheduled Pinned Locked Moved DC Designs Concorde
6 Posts 4 Posters 1.1k Views
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • D Offline
    D Offline
    Delta064
    wrote on last edited by
    #1

    Hi,
    I am still trying to master Concorde using the manual as guidance and one issue I am continually running into is the fact that the aircraft starts to shake and autopilot starts to lose vertical control at speeds above around 320kts indicated.
    The manual says that I should be accelerating to 400kts.
    If no one else is having this problem then I really am confused as to what I must be doing to cause this?

    C 1 Reply Last reply
    0
    • L Offline
      L Offline
      LJToranaXU1
      wrote on last edited by
      #2

      I use this aircraft in FSX. I have found the autopilot a bit touchy on VS especially if you initiate a large change in vertical speed. I generally change vertical speed by incremental changes rather than one big change. As for the shaking above 320KIAS I haven't experienced that and have flown the plane at speeds greater than 320. Are you using Accufeel in your FS? If so check the settings for max airspeed etc as this program causes shaking at near or above the set max airspeed. Hope this helps!

      1 Reply Last reply
      1
      • D Offline
        D Offline
        Delta064
        wrote on last edited by
        #3

        Accu-feel! Bingo!!
        I have turned off Accu-feel for the Concorde and it is like a completely different add-on. Thank you for the suggestion. It's now flying much more like how the manual says it should.
        It might be worth adding to the manual to turn off accu-feel for this add-on. It had the speed limit set to 300kts!
        Thanks again!

        L 1 Reply Last reply
        1
        • D Delta064

          Hi,
          I am still trying to master Concorde using the manual as guidance and one issue I am continually running into is the fact that the aircraft starts to shake and autopilot starts to lose vertical control at speeds above around 320kts indicated.
          The manual says that I should be accelerating to 400kts.
          If no one else is having this problem then I really am confused as to what I must be doing to cause this?

          C Offline
          C Offline
          CptKiddAPI
          wrote on last edited by
          #4

          @Delta064 If you have A2A's Accufeel installed, make sure you turn it off for Concorde. I was racking my brain because I would get wicked shaking and vibration at 320 kts even though the visor was fully retracted along with the landing lights and gear and I had the CG within the two marks on the gauge. Turned out to be accufeel. Once I truned that off problem solved. Hope this helps.

          1 Reply Last reply
          0
          • D Delta064

            Accu-feel! Bingo!!
            I have turned off Accu-feel for the Concorde and it is like a completely different add-on. Thank you for the suggestion. It's now flying much more like how the manual says it should.
            It might be worth adding to the manual to turn off accu-feel for this add-on. It had the speed limit set to 300kts!
            Thanks again!

            L Offline
            L Offline
            LJToranaXU1
            wrote on last edited by
            #5

            @Delta064 You can also adjust up the max KIAS and Mach in the Accufeel menu, this is what I did for the Concorde. Set it for about 500KIAS and Mach 2.1 and the shaking won't interfere with the flight dynamics.

            1 Reply Last reply
            1
            • DC1973D Offline
              DC1973D Offline
              DC1973
              wrote on last edited by
              #6

              Good call guys, I didn't know that Accufeel was causing issues with Concorde. Something to be added in the manual I think!

              1 Reply Last reply
              0
              Reply
              • Reply as topic
              Log in to reply
              • Oldest to Newest
              • Newest to Oldest
              • Most Votes


              • Login

              • Don't have an account? Register

              • Login or register to search.
              • First post
                Last post
              0
              • Categories
              • Recent
              • Tags
              • Popular
              • Users